Excel MK II Soldier & Excel Super Slim Soldier

Available galvanized or painted finish



EX-MK II Soldier Profile

It is used to support the shutter at the corner. Two corner profile of different shutter are tied together using tie bar and wing nut. The aluminium beams are fitted to the profile using universal clamp. The corner profile consist of a right angled bend sheet with holes at specified intervals.

Available sizes are given bellow.

Length (m) 3.60 3.15 2.7 1.8 1.125 0.90 0.675 0.45

 Available galvanized or painted finish

Wall Form Components

EX-MK II Universal Clamps

Connect aluminium beams ( EB 150 ) to Excel Soldiers.

Available EP



EX - MK II Timber Wailing Clamps

Connect timber wailings of any size to Excel Soldiers.

Available EP




EX - MK II WEDGE Clamps

It can be used to fix aluminium beams ( EB 150 ) to the Excel Soldiers where a quick fastening device is preferred.

Available EP


EX-MKII Soldier Hop-Up Brackets

These brackets are support a three board wide working platform which can be fixed at any level. They incorporate a socket to take a guard post of standard scaffold tube. A guard rail of standard tube with scaffold fittings for attachment and a toe board complete the platform.

Available galvanized or painted finish






EX - MK II Lifting Brackets

These brackets are bolted to the top of Soldiers, they provide facilities for lifting by crane.

Available galvanized or painted finish

EX - MK II Support Plate

Where it is necessary to give additional support to the wailings and the form face of the crane handled forms, these can be bolted to the bottom of the Soldiers. They should be fitted on the Soldiers to which the lifting brackets are attached.

Available galvanized or painted finish

EX - MK II Stabilisers

Easily attached to the base of Soldiers they provide a means of plumbing and stabilizing the form for extra safety. If used on one side only the base must be anchored to the ground to prevent uplift. A minimum of two per form is required and high forms may require additional strutting.

Available galvanized or painted finish




EX-MKII END TIE WASHER

Used in conjunction with standard tie rod, nuts, and thrust plate, they enable two Soldiers to be fixed at right angles.

Available galvanized or painted finish


EX - MKII Form Jacks

Primarily used to level a form, they can also be used horizontally as a plumbing device when fitted to climbing form. A minimum of two jacks are required per form.

Available galvanized or painted finish



EX - MK II Rapid Clamps

Rapid clamps are used for wall formworks. The clamp can be around 40% time saving and can be removed quickly.

Available galvanized or painted finish

Vertical Shoring Components

EX-MK II Tubular Shoring Adaptar

Tubular Shoring Adaptor is bolted to the ends of a Soldier, to provide adjustment in fixed steps. In junction with the Threaded Shoring Adaptor it is usable in shoring applications.

Available galvanized or painted finish



EX-MKII Forkhead

Forkheads can be used in place of the Head/Base Plate and will support Excel MK II Soldier and timber or steel beams up to 170mm wide.

Available galvanized or painted finish

EX-MKII HEAD/BASES PLATE

Used to spread the load at the top or bottom of a shore, these can be bolted to the end of the Shoring Adaptors.

Available galvanized or painted finish

EX-MK II Threaded Shoring Adaptor

Threaded Shoring Adaptor is bolts to the end of a Soldier, this attachment provides a screw-threaded fine adjustment.

   
Available galvanized or painted finish




EX-MKII SOLDIER BRACING COUPLER

Soldier Bracing Coupler is fixed to the Soldier, these provide a coupler for the attachment of scaffold tube, required when lacing and bracing is to be attached for applications such as freestanding falsework.

Available galvanized or painted finish



Inclined Shoring Components

EX- MKII Heavy Duty Push-Pull Prob Adaptor

This is used in conjunction with Web Bearing Plates, it provides a strong connection to Soldiers and develops the full load potential of the shore in tension or compression.

Available galvanized or painted finish



EX-MKII Web Bearing Plate

2 nos. of Web Bearing Plates are required to clamp the HD Push-Pull Prop Adaptor to the Soldier at the diamond hole position.

 

Available galvanized or painted finish

EX-MKII Push Pull Bracket

 Push Pull Bracket is used to give a positive connection for up to 3 Shoring Adaptors to Soldiers either horizontally, vertically, or diagonally.   

Available galvanized or painted finish



EX-MKII Swivel Shoring Base

Swivel Shoring Base is designed for use in conjunction with either Threaded or Tubular Shoring Adaptor for bolting inclined shore to a suitable foundation.

Available galvanized or painted finish

Horizontal Shoring Components

EX-MKII Trench Support Plate

The socket fits over the end of shoring adaptors and the angle ledge ensures that the shore is supported safely on the timber or steel wailing. Alternative hole positions are available to suit different depth wailings.  

Available galvanized or painted finish

Circular Formwork Components

EX-MKII Edge Angle

Robust steel angles, available in lengths to suit the height of the soldier, are attached to both ends of the plywood. These facilitate the bending of the plywood and allow joining of adjacent forms.

  

Available galvanized or painted finish

EX-MKII Inner and Outer Fork Arms

 Inner and Outer Fork Arms are fixed to the Edge Angles on the form to allow connection of the Turnbuckles. They are of different lengths to suit internal or external forms.     

Available galvanized or painted finish

EX-MKII Turn Buckles

Standard and short lengths cover the full range of radii. These are connected across the Fork Arms and when adjusted, by extending or retracting the screw, they flex the form to the required radius.

 

Available galvanized or painted finish

EX-MKII Stiffening Braces

They are connected between the Turnbuckle and the center Soldiers after the main curving procedure, to stiffen the unit and lock the curve.   

Available galvanized or painted finish

Excel Supper Slim Soldier

EX-Super Slim Soldier

Modern constructions incorporate unlimited techniques to construct various structural elements. This system designed to cover wide ranges of construction and to withstand the high pressure exerted while pouring concrete members. The soldiers which are produced in many lengths can be assembled in combination to suit any heights of pouring. The system can be used for extensive applications, e.g. single or double soldier shuttering system, inclined support, vertical shoring, horizontal support, supporting beam etc.


All the components of Excel MK II soldiers are suitable for Excel super slim soldiers.

Available sizes are given bellow.



Length (m) 3.60 2.70 1.80 0.90 0.72 0.54 0.36 0.09

 Available galvanized or painted finish

Tie System

Tie Rod

 Tie Rods are continuous threaded rods, and specifically designed and manufactured for use as formwork tie rods for all types of concrete structures. These are two types, Tie rod Ø15 & Tie rod Ø20. 



Wing Nut

A knock-on Wing Nut used in conjunction with tie plates for securing the rods in formwork applications.

Bar size (mm) 15 20





Plastic Sleeve

Plastic sleeve used as a distance keeper between form faces, these allow tie rods to be withdrawn for re-use.

Bar size (mm) 15 20



Plastic Cone

For use with the Plastic Sleeving tube to suit either 15mm or 20mm tie rod.



Water Barrier

Cast into the concrete wall between two tie bars, these allow through-tie systems to be used in water-retaining structures.

Tie Connector (Joint Nut)

Tie connector used for the joining of tie rods. Complete with centre stop to ensure equal spacing or bar inside the connector.

Bar size (mm) 15 20

THRUST PLATE
Used with Wing Nuts, this can be used to clamp wall shutters together.

Tie Bar size (mm)

15

20

Safty System

Guard Post Bracket

This bracket support three standard steel plank a toe board which provides a safe working platform, the bracket has a vertical pipe for fixing the handrail post & a horizontal channel designed to carry timber or steel plank. The Guard Post Bracket is fitted in to the hollow web of the soldier.

Available galvanized or painted finish



Beams

E 20 Timber Beam

E 20 Timber Beams are wooden formwork beams, glued, solid I- beams. E 20 Timber beam for use as a primary or secondary bearer in a wide range of formwork and shoring applications. These can be cut into at any lengths. The standard lengths are given bellow.

Length(m) 2.45 2.90 3.30 3.60 3.90 4.50 4.90 5.90

EB 150 Aluminium Beam

EB 150 Aluminium beam combine the benefits of strength, lightness and easy of handling with consistency, versatility and exceptional durability. These beams are used for wall formwork and heavier slab support applications. These can be cut into at any lengths. The standard lengths are given bellow. 

Length(m) 1.0 1.2 1.8 2.7 3.6 4.2 5.1 5.7 6.4 7.2

Contact us

How can we help you?
T +971 (6) 743 0320
F +971 (6) 743 1074
E This e-mail address is being protected from spambots. You need JavaScript enabled to view it.